Email: info@smartcut.pro

PRO version giver dig mulighed for at bruge den bedste beregningsalgoritme, indstille bredden på klingen, se affald og bruge titlerne på dele i beregningerne.

Vælg en handlingstid:

For additional payment methods write to us

12 hours 95,00 RUB 7 days 400,00 RUB 30 days 1 300,00 RUB 90 days 3 900,00 RUB 365 days 15 000,00 RUB

Forny kodeord

Kildepostens længde Antal Titel
1
2

Gem list (upload ved hjælp af importfunktion)

Liste format:
Del længde Antal Titel
1
2

Gem list (upload ved hjælp af importfunktion)

Smartcut.pro ver. 2020.09.16

If you want to participate in the translation of our site into your native language, write to us

Beregningen kan tage op til et minut

FAQ:

What does this calculator do?

Smartcut.pro allows you to create an optimal scheme for cutting linear isels (rebar, bar, cable, rope, etc.).
Our cutting calculator uses calculation algorithm with the best yield and minimum waste.

Example of a task for a linear cutting calculator:

For example, you need to cut 6 meter boards into: 23 pieces for 1.2m, 12 pieces for 2.3m, 6 pieces for 3m and 17 pieces for 0.8m. How to spend the least amount of initial boards and minimize waste?

Is there an offline version or mobile app with a calculator?

No. The web version of the calculator is adaptive for all types of devices and maximally optimized for fast download with slow Internet, which eliminates the need to create a mobile application or an offline version of the calculator.

How to place a calculator on your site?

Paste this code into your website:
<iframe width="100%" height="500" src="https://smartcut.pro"></iframe>

Cut with a corner cut. Cutting with the ends at an angle (as in the frame of pictures):

If there are two types of segments with different angles (for example, 30 and 60 degrees), you must do two separate calculations for each type of segments. When the angle of all segments is the same (for example, 45 degrees), then this problem of cutting is solved, as usual, by one calculation.
For example, there is a task: cut into 4 types of pieces of length 2m: with a length of 79cm / 75cm ( outer / inner length), 59 / 55cm, 39 / 35cm and 29 / 25cm.
Solution: in the calculator we indicate the MIDDLE length of the segments: 77cm, 57cm, 37cm and 27cm and the length of the workpiece is 1.98m (the length of the blank for cutting 2m minus the difference between the maximum and average length of any segment, it is (59-57)=2 cm. In the resulting map, the cutting points should be marked as in the figure: Corner cutting

Is it planned to develop sheet cutting (2D cutting)?

Yes, in the near future.

How to quickly enter a list of parts, for example from Excel?

Cutting list import

What does the "Title" column mean?

The "title" of the part displayed on the nesting map. It may include any information: marking, section size, part number, etc. This is not a required parameter.

Sended!

For at sikre en betaling skal du logge ind eller registrere!

Deltitler kan kun specificeres i PRO-versionen. Vil du købe et abonnement på PRO-versionen?

Denne funktion er tilgængelig i PRO-versionen. Vil du købe et abonnement på PRO-versionen?

Denne funktion er tilgængelig i PRO-versionen. Vil du købe et abonnement på PRO-versionen?

Denne funktion er tilgængelig i PRO-versionen. Vil du købe et abonnement på PRO-versionen?

Payment verification

Waiting...